1. Xilinx Ise Linux

• Everett Newman
• 2 years ago
• Views:

411283, 806573, 184,. Cromwell Hill 1. 430017, ezd,.

Transcription

1 Santa Clara University School of Engineering Department of Electrical Engineering Tutorial for Xilinx ISE 9.1i WebPACK and Xilinx Spartan 3 Prepared By: Sally Wood, PhD and Shu-Ting Lee(Fall 2007) Outline: I- Project with Xilinx Project Navigator II- Schematic with Xilinx Project Navigator III- Simulation with Xilinx ISE Simulator IV- Hardware Description Language with Xilinx Project Navigator and Xilinx XST V- Implementation and Downloading on Xilinx Spartan 3 VI- Logic and Input/Output Blocks with Xilinx FPGA Editor VII- Xilinx Spartan 3 and Digilent Starter Board 1

2 I- Project with Xilinx Project Navigator: 1- Open Xilinx ISE 9.1i Project Navigator, you can do that either by double-clicking on the Xilinx ISE 9.1i desktop icon, or from Start All Programs Xilinx ISE 7.1i Project Navigator Figure 1. Xilinx Project Navigator initial window BE CAREFUL: When you open the Xilinx Project Navigator, if you have a previous project already open, then you need to close the old project and proceed with creating a new project. 2- Create a new project, from the menus bar do as follows: File new project Project name: tutorial Top-level source type: Schematic Project location: Student s Z: or E: drive Figure 2. Naming the new project 2

3 In the next window: Family: Spartan 3 Device: xc3s200 Package: ft256 Speed grade: -4 Top-level module type: schematic Synthesis Tool: XST (VHDL/Verilog) Simulator: ISE Simulator Generated simulation language: Verilog Source file window, just continue next finish Figure 3. Device properties associated with the project 3- Open a new schematic file in order to enter your circuits. Project new source choose schematic and put a name like: Circuit NOTE: Your top-level schematic should always be a source file. Moreover, all other files that need to be simulated, synthesized, implemented, and configured also need to be source files. There are many source file types; you will mostly use Schematic, Verilog module, and Testbench waveform source files. HINT: If you are not sure whether you have your circuit on a regular schematic file or a schematic source file, check whether you have this schematic file appearing in a hierarchical manner under your project in the sub-window titled sources in project, if yes then your schematic is a source file, else you schematic is not a source file. HINT: When you find that you have created your circuit on a regular schematic file rather than a source file, you need to create a source file, then select, copy and paste your circuit from your schematic file to the schematic source file. BE CAREFUL: When you select, copy and paste some of your circuits from one schematic to another, sometimes the name of the wires return back to their default names, so you need to rename some of the nets all over again. 3

4 Figure 4. Window to choose new source file type as well as file name Figure 5. Newly created schematic source file appearing in an Hierarchical manner 4- If you want to save your schematic source file File save, or use the toolbar icon for save. You can always use the icon next to it, save all, which saves all the changes in all the source files in your current project. BE CAREFUL: When you save a source file with the toolbar icon, make sure you have the source file that you want to save selected in the Sources in Project sub-window. 4

5 II- Schematic with Xilinx Project Navigator: 1-After creating your schematic source file, you need to add the logic gates to your schematic Categories logic, then Symbols and2, for example (and2 is an AND gate with 2 inputs) And to add a rotated symbol: Symbol inv, for example (inv is an inverter), then Orientation Rotate 90 Figure 6. Menu for adding logic symbols You can always select the used symbol on your schematic and right click, which will give you several options like copy, cut and delete, also options like zoom in or out, rotate and mirror, among others. If you double click on a component in your schematic, you will get the following pop-up window: Figure 7. Object Properties window which appears when double-clicking on a symbol 5

6 Later in this tutorial, you will need to access the Object Properties window of some components NOTE: If you want to gain more knowledge regarding a specific symbol, select that symbol and click on the button called Symbol Info which is located at the bottom of the sub-window from which you added the symbol. It will take you to an online documentation site courtesy of Xilinx. Figure 8. Symbol Info button on the bottom of the Symbols sub-window 2- Add text to the page (names of the students, Lab number, Circuit Title, Date) from the tool bar Figure 9. Add text option from the tool bar HINT: Make sure you use large font size while adding text to your schematic, so that it can be readable when you print your schematic. You can change the font size from the following subwindow, which would show at the lower left of the interface. 6

7 Figure 10. Add Text Options sub-window Write the required text in the box, just like done above for circuit1, and as you move the mouse cursor, you will drag this text with it to you preferred location on your schematic. 3- Add wire as connecting nets between different symbols on your schematic, from the tool bar Figure 11. Add wire from the tool bar HINT: Add the symbols and circuit components first to your schematic and then make the net connections between them, this way you will avoid any dangling wires and faulty connections. HINT: If you want to delete a net that you added to your schematic, select the net and after it becomes red you can use the delete button on your keyboard. HINT: If you only want to delete a net segment and not the whole net connection, you have an option that needs to be change as done in the following figure. 7

8 Figure 12. Select Options sub-window 4- Add net names to name all the wires from the tool bar Figure 13. Add net names to the connected wires Figure 14. Add the name of the wire and then drag and drop it on that specific wire on the schematic HINT: If you have a set of net which have increasing set of numbers, for instance X0, X1, X2.etc. you can just write the first one on the Add Net Name Options sub-window and then increase or decrease these name numbers with the arrows on the right side of this box. 8

9 Naming the nets is helpful when the circuit gets complicated and you do not have enough space to make a physical wire connection between two symbols, rather you can extend small wires from each symbol and give these small extensions the exact same net names. This will allow the tool to consider these extensions as part of an actual wire connection between these two symbols. Figure 15. Connecting two symbols by just naming the nets in between BE CAREFUL: When you use specific net names in a schematic source file, you should not use the same net names in any other schematic source file in that same project; otherwise you will basically short those wires together. 5- Add I/O markers (input and output markers), as well as, add input buffers, Ibuf, and output buffers, Obuf, between the input and output markers and the symbols of your schematic Figure 16. Add I/O markers to your schematic inputs and outputs When you want to drop the I/O markers on your schematic, just click on the end-point and the tool will automatically know whether it is an input or an output. You can name the I/O markers by double-clicking on them and changing its name. BE CAREFUL: When you name the I/O marker, choose a name which is different than the net name before the Ibuf or the Obuf. If you choose the same name, you will basically short the buffer input to its output, which is considered to be a schematic error. 9

10 Figure 17. Add ibuf and obuf between the input markers and the symbols of your schematic Figure 18. Example of I/O markers with Ibuf and Obuf connected to and2 logic symbol 6- Add Bus connections, which is basically a wire with not only 1 bit but many bits of transmission. In order to create this bus connection, we will again benefit from the idea of making connection with naming the nets and not using any physical connections. In the figure below, we have outputted a bus of 8 bits from CB8CE, which is an 8 bit counter, and named this thick wire Q(7:0), furthermore we have used only one bit, the most significant one, Q(7), as a clock input for a second counter CB4CE, which is a 4 bit counter. 10

11 Figure 19. Bus connection done by naming the nets 7- After adding all the symbols and making all the required connections and naming the nets, it is necessary that you check your schematic for errors. From the menus tool bar go to: tools check schematic NOTE: When you check your schematic for errors, and it turns out that you have wires which have errors, it is recommended to solve the problem by deleting the erroneous segment of the wire, and rewire properly. 8- Choose the right printer in your lab room and print your schematic source file as a landscape. 9- Make sure you save your work on your drive (Z: drive) not on the C: drive. NOTE: If your schematic design needs more sheet space, you can go to Edit from the menus bar, and change sheet size, and change the C size to an E size. Figure 20. Schematic properties window to change the sheet size 11

12 III- Simulation with Xilinx ISE Simulator: 1- Regarding the simulation: go to Project new source choose Test Bench WaveForm as your source type. Then continue and choose the schematic source file on which you want run your simulations. 2- To explain the simulation process, here is an example of a circuit on a schematic source file Figure 21. Logic circuit example with three inputs and 1 output, representing a 2-1 multiplexer 3- Next you will see a pop-up window just like the following: Figure 22. Initialize Timing window to set up the testbench properties 12

13 Make sure you do exactly like done in the previous figure. Change to falling edge, because we want to observe all the possible combination of the three input signals. This example has three inputs, which means there are 2 3 = 8 distinct input combinations, which explains the reason you should choose Initial Length of Test Bench to be 800 nsec, as well as Clock Time High and Clock Time Low to be 100 nsec. Moreover, in the Clock Information section, select Single Clock, this would be one of the input signals in the circuit. Figure 23. Initial timing diagram which appears after the Initialize timing window 4- After your testbench source file is opened and you can notice the above timing diagram, you have to click on the timing diagram for each input and change its values, so that at the end you will have all the input combinations, in this example, all the input combinations start from 000 to 111. As shown on the figure below: Figure 24. Instances where the inputs need to make transitions from high to low, and from low to high Figure 25. All input combinations starting from 000 to

14 5- After making sure you have added all the input values, save your testbench source file. NOTE: If your testbench does not appear in the hierarchy of source file in the sub-window Sources in Project that means you have not saved you testbench, which you need to do in order to proceed with your simulation. 6- In the Sources window, select the Behavioral Simulation view to see that the test bench waveform file is automatically added to your project. In the Processes tab, click the + to expand the Xilinx ISE Simulator process and double-click the Simulate Behavioral Model process. Figure 26. Behavior Simulation Selection Figure 27. Simulating Design 14

15 7- To view your simulation results, select the Simulation tab Figure 28. Correct simulation result at the output In the simulation mode you will see the following icons, which you can use: Figure 29. Explained simulation mode taskbar buttons IV- Hardware Description Language with Xilinx Project Navigator and Xilinx XST 1- When creating a new project, remember that in the Project Properties window, you need to specify the Preferred Language to the Hardware Description Language (HDL) of your choice, in the following window it is Verilog. 15

16 Figure 30. New project properties window showing the Preferred Language as Verilog 2- After creating the project, go to Project from the menus tool bar New Source select Verilog Module as your source type and name your file. As an example, we will design a full adder module and instantiate it in a 4 bit adder module. Figure 31. New source file window with a Verilog Module file type 3- When you continue with Next you will encounter a window for defining your Verilog source file inputs and outputs. 16

17 Figure 32. Defining the Verilog source file inputs and outputs for the full adder 4- The Verilog code for a full adder is shown in the next figure; this code is in a structural level representation. A full adder is basically an adder with 3 inputs and 2 outputs. The inputs consist of the two 1 bit primary inputs which need to be added as well as the carry in, and the outputs are the 1 bit sum output as well as the carry out. Figure 33. Verilog module of a full adder 5- To check if you have any syntax errors in your Verilog code, go to the Process View options window Synthesis XST Check Syntax (Double Click). 17

18 Figure 34. Check Syntax 6- After creating a Verilog source file for the full adder, we need to create a Verilog source file in the same manner for the 4 bit adder. In this 4 bit adder we will instantiate 4 full adders. The difference between these two source files is clear in the following figure. When we define the inputs for the 4 bit adder module we need to specify the number of bits for our inputs and outputs, in this case 4 bits, which can be translated as an array from 0 to 3, having 0 as the least significant bit (LSB), and the 3 as the most significant bit (MSB). Figure 35. Defining the Verilog source file inputs and outputs of the 4 bit adder 18

19 In the 4 bit adder we have three inputs and 3 outputs. The inputs consist of the two 4 bit numbers as well as the carry in, and the outputs consist of the 4 bit sum output as well as the carry out and the overflow output. Figure 36. Verilog module of a 4 bit adder 7- In order to use the 4 bit adder in our top level schematic, we need to go to the Process View options list and from Design Utilities, choose Create Schematic Symbol. With this step you create a symbol for your 4 bit adder so that you can use it in a schematic source file. You can open the *.sym form menu File Open. Figure 37. Schematic symbol created from the 4 bit adder Verilog module BE CAREFUL: Every time you go back and make a change in your HDL file, you need to redo the step of creating a schematic symbol. NOTE: After you make changes to your HDL file and create a new schematic symbol, when you go back to your schematic file, you will notice that the tool will ask you whether you want to update the changed symbol. 19

20 8- Because we have instantiated 4 full adder module in the 4 bit adder code, notice that in the Sources, in the project options window, you have created a little hierarchy tree, with the 4 bit adder source being the parent of the full adder sources. Figure 38. Hierarchy of the project source files 9- In order to use the created schematic symbol in the top level schematic source file, open the tab where you can choose Symbols from Categories choose <Z:your project folder> from Symbol choose myadder4. Drag this new symbol and use it in your top level schematic source file. Notice that after you save all these source files you will see a hierarchy like shown above. Figure 39. Use the created symbol 20

21 V- Implementation and Downloading on Xilinx Spartan 3: 1- After creating a schematic source file, which has the logic circuit with all the Ibuf s and Obuf s and the corresponding I/O markers, select these buffers, double click on them and you will get the following pop-up window: Figure 40. Buffer properties window 2- On the above figure notice that we don t have an attribute called LOC, (which stands for location), thus you need to create that new trait go to new attribute name: LOC, attribute value: K13, attribute value type: string, as explain in the following figure. Figure 41. Creating a new attribute, LOC, for a buffer 21

22 3- Connect the Xilinx Spartan 3 FPGA board to the computer as well as to the power outlet. BE CAREFUL: When connecting the JTAG connection to its port on the Digilent board, make sure you have the names of the pins on the connection match the ones on the port. HINT: From the Process View sub-window right-click on the Generate Programming File and select the Properties you will get a pop-up window like shown below. Under Readback Options select Enable Readback and Reconfiguation and check the rest of the values. Figure 42. Changing the start up clock to a JTAG clock 22

23 4- In order to download your schematic design on the board, you need to undergo the final configuration of your design from the Process View options scroll down till the end double click Configure Device (impact) You will get a pop-up window called configure device choose Boundary Scan Mode, shown in the following set of figures. Figure 43. Configure Device (impact) from the Processes to source sub-window Figure 44. Pop-up window appearing while configuring a device, 23

24 5- After clicking the Finish in last figure, you will be asked to assign the configuration file (the.bit file) for device xc3s200 by a pop-up, and for the second device xcf02s just click on the Bypass button, as shown in the following figures. Figure 45. Choosing the.bit configuration file for the first device Figure 46. Choosing Bypass for the second device 24

25 6- Select the xc3s200.bit device go to Operations from the menus bar Program ok Figure 47. Program options window for the first device Figure 48. Program was downloaded successfully on the Digilent Spartan 3 Board NOTE: When you get Programming Failed try to program again, most of the time it programs successfully the second time you try. If not, make sure the connection is place properly, and also that you have chosen the right.bit file for the first device, and of course that you are using the right device, in our case the xc3s

26 7- Again from the Process View window of options implement Design place and route Place and Route report (PAR) double click on that and you will get a report file Figure 49. Place and Route Report (PAR) option from the process view sub-window try to locate the device utilization summary you usually need to find out how many input/output buffers (IOB) and logic block slices you have used, also make sure you check that you have no errors, as seen in the following figure. Figure 50. Part of the Place and Route report showing the number of IOB s and Slices used 26

27 VI- Logic and Input/Output Blocks with Xilinx FPGA Editor: 1- You need to examine your implementation by going to FPGA Editor (from the start menu Xilinx ISE 9.1i accessories or from the process view sub-window options) you will get the following window: Figure 51. Xilinx FPGA Editor graphical user interface 2- Go to file open and browse go to your project folder and choose the file which has the name of your schematic that you did and an extension.ncd as shown in the figure below Figure 52. Opening a design with Xilinx FPGA Editor 27

28 3- From the list 1 window change the all components option in the scroll box to routed nets, select one of the nets and then zoom in, in order to find out the route of the specified net. The specified net would turn red when selected. Figure 53. Close view of a selected logic slice 4- If you place the cursor of your mouse on one of the red or blue blocks it will tell you if it is a Slice (logic block) or an IOB (input/output block) with its specific number. Double click on these blocks and you will get a window like the following (this one is the window after selecting a Slice): Figure 54. Inside a slice, which includes two Look-up tables (LUT) and two flip flops 28

29 Notice, in this block, we have two look-up tables (LUT) and two flip flops, if you leave the cursor of the mouse on an LUT or if you click on an LUT, you will get its logic function. LUT set the logic functions, while the flip-flops act as storage elements. Figure 55. Close-up view for a set of one LUT and one Flip flop with all their surrounding circuitry But if you select an IOB and double click, you will get a window like the following figure. Figure 56. Inside an input/output block The inside view of a logic slice is completely different from that of a IOB. HINT: When getting the equation (logic function) of an LUT, sign symbolizes an XOR, and the ~ sign symbolizes an inverse. 29

30 VII- Xilinx Spartan 3 and Digilent Starter Board: The Xilinx Spartan 3 field programmable gate arrays (FPGA) are the most commonly used educational logic device families. The Xilinx Spartan 3 FPGA used in this introductory logic design lab is mounted on the Digilent Starter board, which has many student-friendly features and attributes. The following picture courtesy of Digilent and Xilinx shows the essential parts of this board. Figure 57. Essential parts on an Digilent Xilinx Spartan 3 Starter Board The following are helpful resources for further incite: Spartan-3 Starter Kit Board User Guide Xilinx ISE 9.1 Software Manuals and Help PDF Collection 30

Xilinx ISE. <Release Version: 10.1i> Tutorial. Department of Electrical and Computer Engineering State University of New York New Paltz

Xilinx ISE Tutorial Department of Electrical and Computer Engineering State University of New York New Paltz Fall 2010 Baback Izadi Starting the ISE Software Start ISE from the

More information

Digital Circuit Design Using Xilinx ISE Tools

Digital Circuit Design Using Xilinx ISE Tools Contents 1. Introduction.. 1 2. Programmable Logic Device: FPGA.. 2 3. Creating a New Project.. 2 4. Synthesis and Implementation of the Design.. 11 5.

More information

PCB Project (*.PrjPcb)

Project Essentials Summary The basis of every design captured in Altium Designer is the project. This application note outlines the different kinds of projects, techniques for working on projects and how

More information

RTL Technology and Schematic Viewers

RTL Technology and Schematic Viewers Tutorial [optional] [optional] Xilinx is disclosing this user guide, manual, release note, and/or specification (the 'Documentation') to you solely for use in the development

More information

What is OneDrive for Business at University of Greenwich? Accessing OneDrive from Office 365

This guide explains how to access and use the OneDrive for Business cloud based storage system and Microsoft Office Online suite of products via a web browser. What is OneDrive for Business at University

More information

Creating a Poster in PowerPoint 2010. A. Set Up Your Poster

View the Best Practices in Poster Design located at http://www.emich.edu/training/poster before you begin creating a poster. Then in PowerPoint: (A) set up the poster size and orientation, (B) add and

More information

Windows Movie Maker 2012

Windows Movie Maker 2012 Open Windows Movie Maker A shortcut for Movie Maker should be on the desktop, but if it is not, you can search for the program by touching the right edge of the screen and swiping

More information

Data Visualization. Prepared by Francisco Olivera, Ph.D., Srikanth Koka Department of Civil Engineering Texas A&M University February 2004

Data Visualization Prepared by Francisco Olivera, Ph.D., Srikanth Koka Department of Civil Engineering Texas A&M University February 2004 Contents Brief Overview of ArcMap Goals of the Exercise Computer

More information

Content Author's Reference and Cookbook

Sitecore CMS 6.2 Content Author's Reference and Cookbook Rev. 091019 Sitecore CMS 6.2 Content Author's Reference and Cookbook A Conceptual Overview and Practical Guide to Using Sitecore Table of Contents

More information

KiCad Step by Step Tutorial

KiCad Step by Step Tutorial Copyright 2006 David Jahshan: kicad at iridec.com.au 2011 Update Copyright 2011 Phil Hutchinson Copyright: Please freely copy and distribute (sell or give away) this document

More information

LAB #3 VHDL RECOGNITION AND GAL IC PROGRAMMING USING ALL-11 UNIVERSAL PROGRAMMER

LAB #3 VHDL RECOGNITION AND GAL IC PROGRAMMING USING ALL-11 UNIVERSAL PROGRAMMER OBJECTIVES 1. Learn the basic elements of VHDL that are implemented in Warp. 2. Build a simple application using VHDL and

More information

BIGPOND ONLINE STORAGE USER GUIDE Issue 1.1.0-18 August 2005

BIGPOND ONLINE STORAGE USER GUIDE Issue 1.1.0-18 August 2005 PLEASE NOTE: The contents of this publication, and any associated documentation provided to you, must not be disclosed to any third party without

More information

KiCad Step by Step Tutorial

KiCad Step by Step Tutorial Copyright 2006 David Jahshan: kicad at iridec.com.au Copyright: Please freely copy and distribute (sell or give away) this document in any format. Send any corrections and comments

More information

Ohio University Computer Services Center August, 2002 Crystal Reports Introduction Quick Reference Guide

Open Crystal Reports From the Windows Start menu choose Programs and then Crystal Reports. Creating a Blank Report Ohio University Computer Services Center August, 2002 Crystal Reports Introduction Quick

More information

Model 288B Charge Plate Graphing Software Operators Guide

Monroe Electronics, Inc. Model 288B Charge Plate Graphing Software Operators Guide P/N 0340175 288BGraph (80207) Software V2.01 100 Housel Ave PO Box 535 Lyndonville NY 14098 1-800-821-6001 585-765-2254

More information

Quartus II Introduction for VHDL Users

Quartus II Introduction for VHDL Users This tutorial presents an introduction to the Quartus II software. It gives a general overview of a typical CAD flow for designing circuits that are implemented by

More information

Technical Aspects of Creating and Assessing a Learning Environment in Digital Electronics for High School Students

Xilinx Ise Linux

Session: 2220 Technical Aspects of Creating and Assessing a Learning Environment in Digital Electronics for High School Students Adam S. El-Mansouri, Herbert L. Hess, Kevin M. Buck, Timothy Ewers Microelectronics

More information

Software Version 10.0d. 1991-2011 Mentor Graphics Corporation All rights reserved.

ModelSim Tutorial Software Version 10.0d 1991-2011 Mentor Graphics Corporation All rights reserved. This document contains information that is proprietary to Mentor Graphics Corporation. The original recipient

More information

Introduction to Microsoft Word 2003

Introduction to Microsoft Word 2003 Sabeera Kulkarni Information Technology Lab School of Information University of Texas at Austin Fall 2004 1. Objective This tutorial is designed for users who are new

More information

RAPID PROTOTYPING OF DIGITAL SYSTEMS Second Edition

RAPID PROTOTYPING OF DIGITAL SYSTEMS Second Edition A Tutorial Approach James O. Hamblen Georgia Institute of Technology Michael D. Furman Georgia Institute of Technology KLUWER ACADEMIC PUBLISHERS Boston

More information

Internet Explorer 7. Getting Started The Internet Explorer Window. Tabs NEW! Working with the Tab Row. Microsoft QUICK Source

Microsoft QUICK Source Internet Explorer 7 Getting Started The Internet Explorer Window u v w x y { Using the Command Bar The Command Bar contains shortcut buttons for Internet Explorer tools. To expand

More information

Introduction to LogixPro - Lab

Programmable Logic and Automation Controllers Industrial Control Systems I Introduction to LogixPro - Lab Purpose This is a self-paced lab that will introduce the student to the LogixPro PLC Simulator

More information

Mentor Tools tutorial Bold Browser Design Manager Design Architect Library Components Quicksim Creating and Compiling the VHDL Model.

Mentor Tools tutorial Bold Browser Design Manager Design Architect Library Components Quicksim Creating and Compiling the VHDL Model. Introduction To Mentor Graphics Mentor Graphics BOLD browser allows

More information

ISE In-Depth Tutorial 10.1

ISE In-Depth Tutorial 10.1 R Xilinx is disclosing this Document and Intellectual Property (hereinafter the Design ) to you for use in the development of designs to operate on, or interface with Xilinx

More information

Introduction to Word 2007

Introduction to Word 2007 You will notice some obvious changes immediately after starting Word 2007. For starters, the top bar has a completely new look, consisting of new features, buttons and naming

More information

Most of your tasks in Windows XP will involve working with information

OFFICE 1 File Management Files and Folders Most of your tasks in Windows XP will involve working with information stored on your computer. This material briefly explains how information is stored in Windows

More information

How to georectify an image in ArcMap 10

How to georectify an image in ArcMap 10 The University Library has a large collection of historical aerial photos for some North Carolina Counties ( http://www.lib.unc.edu/reference/gis/usda/index.html

More information

1 Introduction. 2 Project Browser. 3 FlowStone Editor

USER GUIDE C O N T E N T S CHAPTER 1 1 Introduction 3 OVERVIEW.. 4 ABOUT THIS GUIDE..4 CHAPTER 2 2 Project Browser 5 OVERVIEW.. 6 NAVIGATOR.. 6 TOOLBAR..7 PROJECT LIST.. 7 PROJECT ACTIONS.. 9 OPENING

More information

X-Trade Brokers Dom Maklerski S.A. XTB Expert Builder. Tutorial. Michał Zabielski 2010-08-05

X-Trade Brokers Dom Maklerski S.A. XTB Expert Builder Tutorial Michał Zabielski 2010-08-05 Table of Contents Installation..3 Legal notification..7 Initial adjustments / Preferences..8 Language..8 Platform

More information

1. Downloading. 2. Installation and License Acquiring. Xilinx ISE Webpack + Project Setup Instructions

Xilinx ISE Webpack + Project Setup Instructions 1. Downloading The Xilinx tools are free for download from their website and can be installed on your Windowsbased PC s. Go to the following URL: http://www.xilinx.com/support/download/index.htm

More information

USER GUIDE Version 2.0

USER GUIDE Version 2.0 TABLE of CONTENTS Introduction.. 3 Hardware Overview.. 3 Software Overview.. 4 DAYSHIFT Panel.. 5 Settings Panel.. 6 Setup Tab.. 6 Configure.. 6 Show User Guide.. 6 Preview

More information

USER MANUAL FOR. autocue.com

USER MANUAL FOR WINDOWS autocue.com Contents Install the QStart software Registering QStart Using your Starter Series Prompter Prompt output Dual screens Enable a prompt monitor Change the size Change

More information

Introduction to MS WINDOWS XP

Introduction to MS WINDOWS XP Mouse Desktop Windows Applications File handling Introduction to MS Windows XP 2 Table of Contents What is Windows XP?.. 3 Windows within Windows.. 3 The Desktop.. 3 The

More information

Start A New Project with Keil Microcontroller Development Kit Version 5 and Freescale FRDM-KL25Z

Start A New Project with Keil Microcontroller Development Kit Version 5 and Freescale FRDM-KL25Z This tutorial is intended for starting a new project to develop software with Freescale FRDM-KL25Z board

More information

GoodReader User Guide. Version 1.0 GoodReader version 3.16.0

GoodReader User Guide Version 1.0 GoodReader version 3.16.0 Contents Operating GoodReader 1 Send PDF files to Your ipad 2 Copy Files with itunes 2 Copy Files to a Cloud Service 5 Download Files from the

More information

Lab 3: Introduction to Data Acquisition Cards

Lab 3: Introduction to Data Acquisition Cards INTRODUCTION: In this lab, you will be building a VI to display the input measured on a channel. However, within your own VI you will use LabVIEW supplied

More information

Generative Drafting. Page 1 1997 2001 DASSAULT SYSTEMES. IBM Product Lifecycle Management Solutions / Dassault Systemes

Generative Drafting Page 1 Tutorial Objectives Description This Tutorial is an introduction to Generative Drafting. Message To show how CATIA V5 allows the user to automatically generate associative drafting

More information

Installing Remote Desktop Connection

SETTING UP YOUR REMOTE DESKTOP This section will assist you in setting you Remote Desktop Connection. This will allow you to create an icon for easy access to your virtual desktop. DISCLAIMER: All images

More information

Lab - Building an Internet of Things Application Hands-On Lab

Lab - Building an Internet of Things Application Hands-On Lab Table of contents 1. Creating a Bluemix Application.. 3 2. Create and add an Internet of Things Service.. 4 2.Wire the connected device s

More information

WinCC. Configuration Manual. Manual Volume 2

WinCC Configuration Manual Manual Volume 2 This manual is part of the documentation package with the order number: 6AV6392-1CA05-0AB0 Release: September 1999 WinCC, SIMATIC, SINEC, STEP are trademarks

More information

16.4.3 Lab: Data Backup and Recovery in Windows XP

16.4.3 Lab: Data Backup and Recovery in Windows XP Introduction Print and complete this lab. In this lab, you will back up data. You will also perform a recovery of the data. Recommended Equipment The

More information

Simulating Power Supply Sequences for Power Manager Devices Using PAC-Designer LogiBuilder

April 2008 Introduction Application Note AN6044 This application note provides a step-by-step procedure for simulating isppac -POWR1208 designs developed in the PAC-Designer LogiBuilder system, covering

More information

Project Setup and Data Management Tutorial

Project Setup and Heavy Construction Edition Version 1.20 Corporate Office Trimble Navigation Limited Engineering and Construction Division 5475 Kellenburger Road Dayton, Ohio 45424-1099 U.S.A. Phone:

More information

Table Of Contents. iii

Table Of Contents Quickstart.. 1 Introduction.. 1 Data administration.. 1 The Toolbar.. 2 Securities management.. 3 Chart window structure.. 4 Adding an indicator.. 5 Chart drawings.. 6 Saving

More information

DocumentMall PPDM Upload Link Version 1.0 User s Guide

Version 1.0 User s Guide Copyright 2012 All other trademarks are property of their respective owners. The contents of this User s Guide are subject to change without notice. Visit www.documentmall.com/user

More information

Microsoft Access 2010 handout

Microsoft Access 2010 handout Access 2010 is a relational database program you can use to create and manage large quantities of data. You can use Access to manage anything from a home inventory to a giant

More information

TERMINAL Debug Console Instrument

Summary This document describes how to place and use the TERMINAL virtual instrument in an FPGA design. Core Reference CR0180 (v2.0) March 06, 2008 The TERMINAL device is a debug console instrument for

More information

From the list of Cooperative Extension applications, choose Contacts Extension Contact Management System.

1 Illustrated Guide to Creating Labels with Word for Mac 2008 for Mailing Lists in the Extension Contacts Database Note: With most computer tasks, there are multiple ways to achieve the same results. Substitute

More information

After going through this lesson you would be able to:

18 :: Data Entry Operations 2 Operating System 2.1 INTRODUCTION The operating system in these days uses a graphical user interface (GUI). Here you do not have to remember all the commands by heart. The

More information

Browsing and working with your files and folder is easy with Windows 7 s new look Windows Explorer.

Getting Started with Windows 7 In Windows 7, the desktop has been given an overhaul and makeover to introduce a clean new look. While the basic functionality remains the same, there are a few new navigation

More information

Centre for Learning and Academic Development. IT Training. File Management. Windows Vista. Version 1.0 www.skills.bham.ac.uk

Centre for Learning and Academic Development IT Training File Management Windows Vista Version 1.0 www.skills.bham.ac.uk File Management Windows Vista Author: Phil Smith and Linda Clark Version: 1.0, August

More information

TxEIS on Internet Explorer 7

TxEIS on Internet Explorer 7 General Set Up Recommendations: Several modifications will need to be made to the computer settings in Internet Explorer to ensure TxEIS runs smoothly, reports pop up as desired,

More information

5050 Getting Started

5050 Getting Started Getting Started. The 50/50 system is basically made up of four components, the Software Application, Server, J2 Selling Stations (on tables) and the Handheld Selling Units. This manual

More information

Intro to Web Development

Intro to Web Development For this assignment you will be using the KompoZer program because it free to use, and we wanted to keep the costs of this course down. You may be familiar with other webpage editing

More information

Division of School Facilities OUTLOOK WEB ACCESS

Division of School Facilities OUTLOOK WEB ACCESS New York City Department of Education Office of Enterprise Development and Support Applications Support Group 2011 HELPFUL HINTS OWA Helpful Hints was created

More information

OS X LION SET UP THE SYSTEM

OS X LION SET UP THE SYSTEM OS X Lion Set Up the System Last Edited: 2012-07-10 1 Personalize the Interface.. 3 Organize the Desktop.. 3 Configure Apple Trackpad.. 4 Configure Apple Magic Mouse.. 6

More information

13 Managing Devices. Your computer is an assembly of many components from different manufacturers. LESSON OBJECTIVES

LESSON 13 Managing Devices OBJECTIVES After completing this lesson, you will be able to: 1. Open System Properties. 2. Use Device Manager. 3. Understand hardware profiles. 4. Set performance options. Estimated

More information

Select the Crow s Foot entity relationship diagram (ERD) option. Create the entities and define their components.

Α DESIGNING DATABASES WITH VISIO PROFESSIONAL: A TUTORIAL Microsoft Visio Professional is a powerful database design and modeling tool. The Visio software has so many features that we can t possibly demonstrate

More information

FPGA Synthesis Example: Counter

FPGA Synthesis Example: Counter Peter Marwedel Informatik XII, U. Dortmund Gliederung Einführung SystemC Vorlesungen und Programmierung FPGAs - Vorlesungen - VHDL-basierte Konfiguration von FPGAs mit dem

More information

QUICK START GUIDE. SG2 Client - Programming Software SG2 Series Programmable Logic Relay

QUICK START GUIDE SG2 Client - Programming Software SG2 Series Programmable Logic Relay SG2 Client Programming Software T he SG2 Client software is the program editor for the SG2 Series Programmable Logic

More information

Florence School District #1

Florence School District #1 Module 2: SMART Board Basics and Beyond 1 SMART Board Software and Beyond In SMART Notebook software, you can create or open SMART Notebook software (.notebook) files. After

More information

1.5 MONITOR. Schools Accountancy Team INTRODUCTION

1.5 MONITOR Schools Accountancy Team INTRODUCTION The Monitor software allows an extract showing the current financial position taken from FMS at any time that the user requires. This extract can be saved

More information

SMART Sympodium and Notebook Software 9.5

SMART Sympodium and Notebook Software 9.5 What is a SMART Sympodium? Equipped with the same software as SMART Board interactive whiteboards, SMART Sympodium interactive pen displays are perfect for presenting

More information

Excel 2007: Basics Learning Guide

Excel 2007: Basics Learning Guide Exploring Excel At first glance, the new Excel 2007 interface may seem a bit unsettling, with fat bands called Ribbons replacing cascading text menus and task bars. This

More information

Updox, LLC support@updox.com 614-547-9635

Set Up and User Guide Version 3.2.2 Updox, LLC support@updox.com 614-547-9635 Table of Contents Creating and Managing Internal Updox Users.. 3 How to Send and Receive Faxes.. 4 How to Import Files into

More information

Adobe Dreamweaver CC 14 Tutorial

Adobe Dreamweaver CC 14 Tutorial GETTING STARTED This tutorial focuses on the basic steps involved in creating an attractive, functional website. In using this tutorial you will learn to design a site

More information

10.3.1.6 Lab - Data Backup and Recovery in Windows XP

5.0 10.3.1.6 Lab - Data Backup and Recovery in Windows XP Introduction Print and complete this lab. In this lab, you will back up data. You will also perform a recovery of the data. Recommended Equipment

More information

Loyalty Program Guide

Loyalty Program Guide 110911 2011 Blackbaud, Inc. This publication, or any part thereof, may not be reproduced or transmitted in any form or by any means, electronic, or mechanical, including photocopying,

More information

Teacher Training Session 1. Adding a Sub-Site (New Page) Editing a page and page security. Adding content cells. Uploading files and creating folders

Teacher Training Session 1 Adding a Sub-Site (New Page) Editing a page and page security Adding content cells Uploading files and creating folders Adding Sub Sites Sub Sites are the same as Sub Groups

More information

The 104 Duke_ACC Machine

The 104 Duke_ACC Machine The goal of the next two lessons is to design and simulate a simple accumulator-based processor. The specifications for this processor and some of the QuartusII design components

More information

PigCHAMP Knowledge Software. Enterprise Edition Installation Guide

PigCHAMP Knowledge Software Enterprise Edition Installation Guide Enterprise Edition Installation Guide MARCH 2012 EDITION PigCHAMP Knowledge Software 1531 Airport Rd Suite 101 Ames, IA 50010 Phone (515)

More information

Ansur Test Executive. Users Manual

Ansur Test Executive Users Manual April 2008 2008 Fluke Corporation, All rights reserved. All product names are trademarks of their respective companies Table of Contents 1 Introducing Ansur.. 4 1.1 About

More information

Adobe Digital Signatures in Adobe Acrobat X Pro

Adobe Digital Signatures in Adobe Acrobat X Pro Setting up a digital signature with Adobe Acrobat X Pro: 1. Open the PDF file you wish to sign digitally. 2. Click on the Tools menu in the upper right corner.

More information

Workspaces Creating and Opening Pages Creating Ticker Lists Looking up Ticker Symbols Ticker Sync Groups Market Summary Snap Quote Key Statistics

Getting Started Workspaces Creating and Opening Pages Creating Ticker Lists Looking up Ticker Symbols Ticker Sync Groups Market Summary Snap Quote Key Statistics Snap Report Price Charts Comparing Price

More information

Web Conferencing Demo and Tutorial

Web Conferencing Demo and Tutorial Overview Share presentations, documents, Web content & applications with individuals and groups around the world Adds a visual component to a conference call Enhances

More information

BID2WIN Workshop. Advanced Report Writing

BID2WIN Workshop Advanced Report Writing Please Note: Please feel free to take this workbook home with you! Electronic copies of all lab documentation are available for download at http://www.bid2win.com/userconf/2011/labs/

More information

SMART Board Tips & Tricks (version 9.0) Getting Started. SMART Tools vs. SMART Notebook software

SMART Board Tips & Tricks (version 9.0) Getting Started SMART Tools vs. SMART Notebook software Click the SMART Board icon (in the system tray at the bottom right of your screen) to access the SMART Board

More information

Online Sharing User Manual

Online Sharing User Manual June 13, 2007 If discrepancies between this document and Online Sharing are discovered, please contact backupfeedback@verizon.net. Copyrights and Proprietary Notices The information

More information

Module 1: Getting Started With Altium Designer

Module 1: Getting Started With Altium Designer Module 1: Getting Started With Altium Designer 1.1 Introduction to Altium Designer.. 1-1 1.1.1 The Altium Designer Integration Platform..1-1 1.2 The Altium

More information

Content Management System Help. basic tutorial on Evergreen s CMS

Content Management System Help cms.evergreen.edu Tips, tricks and basic tutorial on Evergreen s CMS Contents Vocabulary Login Opening a page Editing a page Creating a new page Inserting internal and external

More information

Instructions for creating a data entry form in Microsoft Excel

1 of 5 You have several options when you want to enter data manually in Excel. You can enter data in one cell, in several cells at the same time, or on more than one worksheet (worksheet/spreadsheet: The

More information

Virtual Office Remote Installation Guide

Virtual Office Remote Installation Guide Table of Contents VIRTUAL OFFICE REMOTE INSTALLATION GUIDE.. 3 UNIVERSAL PRINTER CONFIGURATION INSTRUCTIONS.. 12 CHANGING DEFAULT PRINTERS ON LOCAL SYSTEM..

More information

LESSON 7: IMPORTING AND VECTORIZING A BITMAP IMAGE

LESSON 7: IMPORTING AND VECTORIZING A BITMAP IMAGE In this lesson we ll learn how to import a bitmap logo, transform it into a vector and perform some editing on the vector to clean it up. The concepts

More information

Tutorial: Configuring GOOSE in MiCOM S1 Studio 1. Requirements

Tutorial: Configuring GOOSE in MiCOM S1 Studio 1. Requirements - Two (2) MiCOM Px4x IEDs with Version 2 implementation of IEC 61850 - Two (2) Cat 5E Ethernet cable - An Ethernet switch 10/100 Mbps - MiCOM

More information

Instructions for Importing (migrating) Data

Instructions for Importing (migrating) Data from CTAS Version 7 to CTAS Version 8 For Windows 8 and 8.1 CTAS Version 8 is designed to work with your Version 7 data if you choose to. These instructions

More information

Installing Lync. Configuring and Signing into Lync

Microsoft Lync 2013 Contents Installing Lync.. 1 Configuring and Signing into Lync.. 1 Changing your Picture.. 2 Adding and Managing Contacts.. 2 Create and Manage Contact Groups.. 3 Start an Instant

More information

Jump-Start Tutorial For ProcessModel

Jump-Start Tutorial For ProcessModel www.blueorange.org.uk ProcessModel Jump-Start Tutorial This tutorial provides step-by-step instructions for creating a process model, running the simulation, and viewing

More information

Chapter 1. Creating Sketches in. the Sketch Mode-I. Evaluation chapter. Logon to www.cadcim.com for more details. Learning Objectives

Chapter 1 Creating Sketches in Learning Objectives the Sketch Mode-I After completing this chapter you will be able to: Use various tools to create a geometry. Dimension a sketch. Apply constraints to

More information

CCNA Discovery 4.0.3.0 Networking for Homes and Small Businesses Student Packet Tracer Lab Manual

4.0.3.0 Networking for Homes and Small Businesses Student Packet Tracer Lab Manual This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial

More information

NHS Professionals Online Management Information System Training Manual Management Information Training Manual

NHS Professionals Online Management Information System Training Manual Author and Creation date: Mark Frost October 2010 Page 1 Contents Page 1. Getting Started..3 2. Overview..4 3. The System Toolbar..5

More information

Database Studio is the new tool to administrate SAP MaxDB database instances as of version 7.5.

1 2 3 4 Database Studio is the new tool to administrate SAP MaxDB database instances as of version 7.5. It replaces the previous tools Database Manager GUI and SQL Studio from SAP MaxDB version 7.7 onwards

More information

Horizon Patient Folder User s Guide

Horizon Patient Folder User s Guide - 1 - Overview St. Mary's Medical Center is embarking on a new way to view the medical record for patients on-line. This information will guide you through the Horizon

More information

Making Your Computer Work for You Tips for Windows 7, Laptops, Internet Explorer, MS Office and Adobe Acrobat

Making Your Computer Work for You Tips for Windows 7, Laptops, Internet Explorer, MS Office and Adobe Acrobat By Drew Kottke Bureau of Technical Services Division of Transportation Systems Development

More information

PRODUCTIVITY THROUGH INNOVATION 600 CONTROL DIRECT DRIVE TECHNICAL/OPERATION MANUAL

Rev. D PRODUCTIVITY THROUGH INNOVATION 600 CONTROL DIRECT DRIVE TECHNICAL/OPERATION MANUAL 10 BORIGHT AVENUE, KENILWORTH NEW JERSEY 07033 TELEPHONE: 800-524-0273 FAX: 908-686-9317 TABLE OF CONTENTS Page

More information

EqualSkills Syllabus Version 2.0

EqualSkills Syllabus Version 2.0 Copyright 2011 ECDL Foundation All rights reserved. No part of this publication may be reproduced in any form except as permitted by ECDL Foundation. Enquiries for permission

More information

6 USING WINDOWS XP 6.1 INTRODUCTION

6 USING WINDOWS XP 6.1 INTRODUCTION The windows operating system started with the introduction of Windows OS and Windows for work group for networking. Since then it has come a long way and Windows 95,

1143 tale of the comet pdf to jpg. 1143 Tale Of The Comet Pdf Files. In economics, physical capital or just capital is a factor of production (or input into the process of production), consisting of.

More information

Appointment Scheduler

EZClaim Appointment Scheduler User Guide Last Update: 11/19/2008 Copyright 2008 EZClaim This page intentionally left blank Contents Contents.. iii Getting Started.. 5 System Requirements.. 5 Installing

More information

Applications and Account Manager Dashboard User Guide

www.textbuster.com 1 Applications and Account Manager Dashboard User Guide For Android phones www.textbuster.com 2 Downloading the TextBuster applications After the TextBuster device is installed into

More information